 |
Search within results Refine by |
Triple E's award-winning UNITRACK System is ideal for both touring and permanent installations.
from $39.95
|
Four curved Triple-E Track section sizes.
from $393.65
|
For straight track systems. Normal spacing is every 12" apart. 55 lb. SWL.
$24.30
|
For straight track only. The curtain stacks offstage.
$50.55
|
For curved track systems. Normal spacing is every 12" apart. 55 lb. SWL.
$34.80
|
Weighted or screwed to the floor, the pulley is adjustable in height.
$107.30
|
Pre-stretched matte black polyester cord 5/16" in diameter used to operate all Triple E systems.
$1.65
|
Bolts to the top of the track and guides the operating cord around the top of the track system.
$85.10
|
For curved systems, it can divert the operating cord up or down towards a motor or floor pulley.
$233.85
|
Same as TRA 20, but for use on track over 70' long and for motorized systems.
$371.35
|
Same as master carrier (TRA 07) but with rope clamping arm that guides the cord through
$192.80
|
Diverts the operating cord above the track back towards the head pulley.
$115.65
|
Must be used on curved track systems between the track and other suspensions.
$49.20
|
Used for suspending tracks from rope or wire rope. Tested to 330 lbs. SWL.
$18.35
|
$90.00
|
|
$110.00
|
|
$300.00
|
|
$350.00
|
|
$278.00
|
|
$55.00
|
Used for the ends of all tracks to anchor the trailing edge of the curtains.
$18.85
|
Used in conjunction with scenery carriers and when there is no curtain to anchor.
$18.85
|
Used on flown or movable track systems.
$83.55
|
|
Used to suspend the track from I-beams.
$62.25
|
For use with straight rack systems; the head pulleys diverts the cord down to the floor.
$113.50
|
Set consists of 4 spigots, 1 joint bolt with nut and 2 washers. Used for joining straight UNITRACK sections together.
$15.15
|
Used on the return side of overlap tracks.
$18.85
|
Used on the leading edge of curtains for overlapping tracks
$108.75
|
For use on single tracks with overlap arms. Used with pulley set #TRA31.
$111.25
|
Used with pipe clamps (TRA 14) so that when an overlap track is attached to a single pipe or truss, the tracks hang centered under the pipe.
$21.05
|
Used in conjunction with master carriers on single tracks to create an overlap.
$31.65
|
Used on straight and curved track to maintain track spacing and keep the tracks rigid where they overlap.
$27.65
|
Used for attaching track to any size pipe or truss with an OD range of 1.5" to 2"
$51.80
|
|
$26.50
|
|
May be retrofitted to TRA-06 to make TRA06R or to TRA06C if used on straight track sections.
$27.00
|
|
Used on straight track systems with head pulley to return the operating cord.
$88.50
|
Used with TRA 28 and TRA 28AHD to carry pieces varying from 1/4" to 2".
$78.15
|
Used for carrying heavy scenery on both straight and curved track.
$244.50
|
Used to carry flats on both straight and curved track layouts.
$98.35
|
|
Scenery Carrier Arm - Heavy Duty
$113.70
|
|
Used with carrier TRA28A when carrier is to be used on corded curved tracks.
$77.40
|
|
This is used when scenery or curtains need to meet in the center of the track.
$166.15
|
|
Together, these divert the cord to and from the floor pulley or motor (three parts).
$232.70
|
|
This bolts to an existing hole in the side of a master runner or scenery carrier and is used to secure the cord.
$55.35
|
|
These are used at 3 meter centers to support the cord and prevent sag over longer distances.
$112.50
|
|
$74.25
|
|
$67.75
|
Set consists of 150mm lengths of M12 studding supplied with four nuts and washers.
$19.80
|
Track mounted motorized control system for Unitrack or Unibeam.
$8,301.65
|
Nothing could be easier then a system of Triple E Unitrack with everything you need, packaged and ready for touring and temporary installation.
|
Used to attach the track to a wall or vertical surface. Used with studding (TRA 18).
$42.25
|